Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Are you interested in help around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily obtainable, the project can move easily; if you have to open a wall surface to get rid of the old bathtub and position the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will need an assistant to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and fit trying it. As opposed to hiring a contractor to take over a halfway-completed project, it is better to consider using one before you start. Chances are you may require an expert plumber to make tube links.
This article will aid you set up a new bath tub in your shower room if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and material list should make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather troublesome because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin making sure that the washers are in area in between the tap and the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bathtub in the needed setting. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water system as well as inspect all joints and new pipework for leaks and tighten them if essential. Fill the bath tub and also check the overflow outlet and also the normal electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bath tub should wait until the bathtub has been utilized a minimum of when as this will certainly settle it into its final position.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write a remark down below. We will be interested to see your opinion about this write-up. In hopes that you come back again soon. Sharing is nice. You won't know, you may just be helping someone out. I praise you for your time. Come back soon.
Get the best, call! Report this page